Hioki HiTester 3293-50 Flip-Display True RMS Clamp-Meter , 1mA to 1,000A AC Leakage and Load Current, Conductors to 24mm, Frequency Measurement

Pay with

Hioki HiTester 3293-50 Flip-Display True RMS Features

• Digital clamp-meter measures a wide range of AC from 1mA to 1,000A and frequency to 400Hz

• True RMS sensing meter provides accurate readings when measuring linear or non-linear loads, regardless of waveform

• Clamp measures current without touching or interrupting the circuit, has a jaw opening of 24mm (0.94 inches), and has 11mm (0.43 inches) thick jaws that can open and close independently of one another

• Display can be flipped open and adjusted to a convenient viewing angle

• Meets IEC safety standard 61010, and is rated for CAT III installations to 300V

About Hioki HiTester 3293-50 Flip-Display True RMS

The Hioki 3293-50 digital clamp-meter is a true RMS sensing, auto-ranging meter for measuring a wide range of current, from leakage to load, and frequency in electrical testing applications. It has a clamp that measures AC (alternating current) from 1mA (milliampere) to 1,000A and frequency to 400Hz (hertz). The clamp has two jaws that can close around an electrical conductor up to 24mm (0.94 inches) in diameter to measure current without touching or interrupting the circuit. Each jaw can be opened can closed independently of the other and is 11mm (0.43 inches) thick to fit between narrowly spaced conductors. The meter powers on when the jaws are opened, has a 6,000-count LCD that shows the reading numerically and in a 91-segment bar graph, and has a backlight for visibility in low light that turns off automatically after 15 seconds. The display can be flipped open and adjusted to a convenient viewing angle. The meter features a low-pass filter that reduces high-frequency interference to allow accurate measurements of leakage current and complex wave shapes. The maximum value function shows the highest displayed reading. To aid documentation of readings and capture readings in tight spaces, the data hold function keeps the most recent reading on the display after disconnecting from the circuit. The unit operates on a single CR2032 battery, and turns off automatically after 10 minutes of non-use to conserve battery life. It has a low-battery indicator that signals when the battery needs to be replaced. This true RMS (root mean square) sensing meter provides accurate readings when measuring linear or non-linear loads, regardless of the waveform. It is auto-ranging, so it automatically selects the appropriate operating range. specifications vary according to the range being measured. The meter meets IEC (International Electrotechnical Commission) safety standard 61010 and is rated for CAT (category) III installations to 300V, which covers equipment in fixed installations, such as switches in the fixed installation and some industrial equipment that is permanently connected to the fixed installation. It has CE (European Conformity) marking. The unit comes with a carrying case. Specifications Maximum AC (alternating current) input 1,000A Maximum frequency detected 400Hz Installation rating CAT III, 300V Standards met IEC safety standard 61010; CE marking Power supply CR2032 battery Weight 135g/4.8oz. Dimensions (H x W x D) 130 x 50 x 26mm/5.12 x 1.97 x 1.02 inches H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from front to back. Clamp-meters, also called clamp-on meters, have two jaws that fit around a conductor to measure electrical current without cutting through wires, or touching or interrupting the electrical circuit. Available in handheld or benchtop models, clamp-meters diagnose problems in electrical equipment, wiring, and power supplies. All clamp-meters test for current. Some come with test leads and inputs for measuring voltage, capacitance, and resistance. They display information either in analog or digital form. Factors that influence meter choice include the electrical properties to be measured, the anticipated range of results, and the desired level of protection against transient voltage. Safety ratings are based on International Electrotechnical Commission (IEC) standards for low-voltage test equipment. IEC 61010 delineates four overvoltage installation categories. In general, a meter with a category IV rating will provide more protection against transient voltages than a meter with a lower category rating. Hioki manufactures memory recorders, automatic test equipment, and electronic testing and measurement instruments. The company, founded in 1935, is headquartered in Japan and has a U.S. office in Cranbury, NJ. What's in the Box? Hioki 3293-50 digital clamp-meter CR2032 battery S