We specialize in hard to find items
(1)
Amprobe ACD-3300 IND CAT IV True-RMS Clamp Meter with Temperature
Share Tweet
*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown
- Electrical items MAY be 110 volts.
- 7 Day Return Policy
- All products are genuine and original
About Amprobe ACD-3300 IND CAT IV True-RMS Clamp Meter
The Amprobe ACD-3300 digital clamp meter with included temperature probe is a true RMS (root mean square) sensing, auto- or manual-ranging multimeter for measuring current, voltage, capacitance, and resistance in electrical testing and heating, ventilation, and air conditioning (HVAC) applications. It has a clamp that measures alternating current (AC) to 1,000 amp. The meter comes with detachable test leads that measure direct current (DC) voltage to 1,000 volts (V), AC voltage to 750V, capacitance to 6.6 millifarads, resistance to 66 megaohms, frequency to 1 megahertz (MHz), and duty cycle up to 95%. The clamp has two jaws that can close around a conductor up to 2" (57 mm) in diameter to measure current or frequency without touching or interrupting the circuit. The meter comes with a K-type thermocouple probe for measuring temperature. The peak + or - function records peak positive or negative values for AC current and AC voltage. The maximum or minimum reading mode displays the highest or lowest reading in a session to track a sudden increase or decrease in readings. It has a liquid crystal display (LCD) that shows readings both in digits and on a 66-segment bar graph. The LCD is backlit for visibility in low light. An audible continuity sensor confirms that the circuit conducts electricity, and a diode test detects whether a circuit’s diodes are working properly. The hold function keeps the reading on the display, even after the meter is disconnected. The unit automatically turns off after 30 minutes of non-use to conserve battery life, and a low-battery indicator signals when the meter's batteries need to be replaced. A finger guard on the body of the meter helps protect fingers from shock.This true RMS (root mean square) sensing meter provides accurate readings when measuring linear loads, such as standard induction motors and incandescent lights, where the current or voltage has a sinusoidal waveform, or non-linear loads, such as electronic devices or motors, where the current or voltage has a sinusoidal non-sinusoidal waveform. Two ranging modes (auto or manual) offer a range of operator control when taking readings. When turned on, the meter will be in auto-ranging mode and will automatically select the correct operating range for the property being measured. It can be switched to manual-ranging mode, which requires that the operator choose the appropriate operating range. The meter has a 6,600-count resolution, meaning it can display up to 6,599 units (3-3/4 digits) before the operating range needs to be changed. It meets International Electrotechnical Commission (IEC) safety standard 61010 and is certified for category III installations up to 1,000V, which covers items used with enclosed building circuit installations (service panel parts, branch circuits, and fixed installations that are connected directly to a building's AC power supply), and category IV installations up to 1,000V, which covers measurements at the source of the low-voltage supply, such as electricity meters and overcurrent protection devices. The unit comes with a soft vinyl carrying case.SpecificationsMaximum alternating current (AC) input1,000 ampMaximum AC voltage input750 volts (V)Maximum direct current (DC) voltage input1,000VMaximum capacitance detected6.6 millifaradsMaximum resistance detected66 megaohmsMaximum frequency detected1 megahertz (MHz)Duty cycle measurement range5 to 95%Temperature measurement range-30 to 1,842 degrees Fahrenheit/-35 to 1,000 degrees CelsiusPower supply9V NEDA 1604, JIS 006P, or IEC 6F22 battery (one, installed)Standards met and certificationsEuropean Normal (EN); International Electrotechnical Commission (IEC) and EN safety standard 61010-1; European Conformity (CE); Underwriters Laboratories (UL); Australia N10140Weight1.10 lb./500 gMeter dimensions11 x 4.1 x 2.1 inches/279 x 103 x 53 mm (H x W x D)H is height, the vertical distance from the lowest to highest point; W is width, the horizontal distance from left
