We specialize in hard to find items
All Categories
Portable tinysa Spectrum Analyzer - AURSINC V0.3.1 Hand Held Frequency Analyzer | 100kHz to 960MHz MF/HF/VHF UHF Input | ESD Protected Function & 2.8 inch Touchscreen | Signal Generator
Share Tweet
*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown
- Electrical items MAY be 110 volts.
- 7 Day Return Policy
- All products are genuine and original
- Cash On Delivery/Cash Upon Pickup Available
Portable tinysa Spectrum Analyzer - AURSINC V0.3.1 Features
-
[Upgraded Version: ESD Protection Diodes] Produced by Hugen, tinysa with latest hardware V0.3.1, the displayed version info is "ESD protected" meaning the diodes are installed which will be more stable and sensitive with higher antistatic level and longer service life. NOTE: Due to the old inventory might mix with the new batch, and If you got the old version TinySA and want a new one, you could apply a replacement for it.
-
[Frequency Range] Spectrum analyzers like the tinysa use a resolution filter that is used to isolate the input power in a small frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. But with increase of the frequency span and decrease of the RBW the scanning speed decreases quickly. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes.
-
[2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator that is used for automatic self test and low input calibration. The tinysa contains all the components of a conventional heterodyne swept spectrum analyzer. Color display showing 290 scan points covering up to the full low or high frequency range
-
[4 Input/Output Spec Modes] The input/output specification of the tinysa is split over the 4 modes: Low input mode, High input mode, Low output mode, High output mode. Spectrum Analyzer with two inputs, high quality MF/HF/VHF input for 0.1MHZ-350MHz, lesser quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters for both ranges between 2.6kHz and 640kHz. The firmware of the tinySA can be updated by the user, For newest firmware version update, please refer to : tinysa.org
-
[PC Control] The USB interface implements the Serial over USB (CDC) protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform measurements or update internal settings. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel. Two softwares to control the tinysa are available. Both are able to capture the screen of the tinysa
About Portable Tinysa Spectrum Analyzer - AURSINC V0.3.1
Specification User interface Display resolution 320*240 pixelsScreen diagonal 2.8"16 bits per RGB pixelsResistive touch controlJog switch controlUSB serial port controlOptional TTL USART port (SW not yet implemented) on the internal PCBLinear power supply to avoid switching noise The input/output specification of the tinySA is split over the 4 modes Low input mode spec High input mode spec Low output mode spec High output mode spec Details please visit: https://tinysa.org/wiki/pmwiki.php?n=Main.Specification Reference generator specOptional square wave output with fundamental at -25dBm connected to high input/outputFrequency can be set to 1MHz, 2MHz, 4MHz, 10MHz, 15MHz or 30MHz. Battery specCharging time max 1 hour on 500mA minimum USB port or USB chargerOperation on fully charged battery for at least 2 hours Package Content1x Tiny Spectrum Analyzer
