CN-ZF 50pcs Small Ceramic Tile Leveler and 200PCS Tiles Leveler Spacers(1/16” & 5/64”),The Latest Reusable Small Tile Leveling Tools Flooring Level Tile levellers Set for Builing Walls & Floors

Pay with

CN-ZF 50pcs Small Ceramic Tile Leveler and 200PCS Features

• HARDNESS : These tile levelers are different from other ordinary products in that they use POM (polyacetal pom) The material has high strength and is not easily damaged. T-needle with 430 Stainless round design galvanized for wear and corrosion resistance, Easy to use for DIY operation. Re-usable wedges. save your money.

• EASY TO USE and EFFICIENT: The New small Innovative tile Leveling system ,Smaller body, more convenient operationhelps DIY and Professional tile layers increase the efficiency of laying tiles and obtain a perfect, lippage-freefinish.

• LATEST UPGRADED :These Tile Leveling System the minimum spacing has been reduced to 1.5mm (1/16in) after laying; Suitable for tile gap 1.5mm (1/16in)--3.5mm (9/64in).

• GOOD APPLICABILITY : These ceramic levelers suitable for 3mm(1/8in) to15mm(19/32in) thickness of the tile, These tile levelers Virtually lippage free, flat surface drastically. Reduces the need for grinding and polishing.

• OUR PROMISE : We will always provide you with quality products and good service, if you don't like it, we promise to replace the product or unconditional refund. We welcome you to contact us at any time, we will provide you with a satisfactory solution.

About CN-ZF 50pcs Small Ceramic Tile Leveler And 200PCS

What will you get: 1. 50 pcs tile Leveler +1 pcs special spanner 2 .100 pcs cross spacer (1.5mm)(1/16in)+ 100 pcs cross spacer (2.0mm)（5/64in） How to use? 1 lay the first piece of brick, seam ≥1.5mm(1/16in) or above, and close to second bricks； 2 Insert the T-pin along the crack, then rotate it 90 degrees, clamp the T-pin at the bottom of the two bricks and tighten the adjusting cover so that the two bricks are in the same level； 3 Before the cement or tile glue has completely dried up (usually no more than 3-4hours), tighten the adjusting cover in the opposite direction, then rotate the T-pin 90 degrees so that the T-pin turns to a zigzag parallel to the tile, and remove the leveler; 4 Clean and dry storage for reuse. Make the following three steps in advance to avoid being unable to take out the t-type leveler for reuse: 1. Tile slitting 1.5mm or above, preferably use with cross card; 2.Clean up the cement and debris around the T-needle before installation; 3. After construction, the product must be removed before the cement/binder is completely solidified (please read the instructions of the layer material used carefully) Tip: 1 When the T-needle is stuck in the bottom of the two tiles, shake it slightly from side to side to make some room for easier removal and reuse. 2 When laying the tiles with length more than 80CM (31.5 inches), the distance between two T-needles shall be kept less than 60CM (23 inches), or add one more T-needle in this side. Specification: Material:POM(polyacetal pom) + 430 Stainless Steel Quantity: 50 Sets/Bag + 1Pcs Tool Suitable Space:1.5 mm(1/16in)-3.5 mm(9/64in) Space Tile thickness:3 mm(1/8in)-15 mm(19/32in) Color: As showed in the picture Please note: this product is not suitable for use when the cement layer or the rubber layer is less than 3mm(1/8in) in brick laying construction.