We specialize in hard to find items
All Categories
CenryKay Timer Delay Controller Module DC 5V 12V 24V Delay-Off Cycle Timer Adjustable Trigger Delay Switch Control Relay Board with LCD Display
Share Tweet
*Price and Stocks may change without prior notice
*Packaging of actual item may differ from photo shown
- Electrical items MAY be 110 volts.
- 7 Day Return Policy
- All products are genuine and original
- Cash On Delivery/Cash Upon Pickup Available
CenryKay Timer Delay Controller Module DC 5V 12V Features
-
💚With LCD display, the current mode and parameters are clear at a glance, clear, simple and practical.
-
💚Support high and low level trigger, switch control, suitable for most occasions.
-
💚Wide voltage power supply (6 ~ 30V) supports micro USB 5.0V power supply, which is very convenient to use.
-
💚One-key emergency stop function (STOP key), with reverse connection protection, reverse connection will not burn.
-
💚Different OP, CL, LOP parameters can be set, these parameters are independent of each other and saved separately.
About CenryKay Timer Delay Controller Module DC 5V 12V
Product parameters: Working voltage: 6--30V support micro USB 5.0V power supply; Trigger signal source: high level trigger (3.0V~24V), low level trigger (0.0V~0.2V), switch control (passive switch); Output capability: can control within 30v 5A of DC or AC Equipment within 220v5A; Quiescent current: 15mA Working current: 50mA; Service life: more than 100,000 times; Working temperature: -40- -85°C; Size: 8.0*3.8*1.9cm; Features: With optocoupler isolation, enhanced anti-interference ability, industrial-grade circuit board, setting parameters will be remembered forever after power off. Operating mode: P1. After the signal is triggered, the relay is turned on for the OP time, and then disconnected; within the OP time, the signal is triggered again and is invalid; P2. After the signal is triggered, the relay is turned on for the OP time, and then disconnected; within the OP time, the signal is triggered again to re-time; P3. After the signal is triggered, the relay is turned on for the OP time, and then disconnected; During the OP time, the signal triggers the reset again, the relay is disconnected, and the timing is stopped; P4. Give the trigger signal, after the relay is disconnected for the CL time, the relay is turned on for the OP time, and after the timing is completed, the relay is disconnected; P5. Give the trigger signal, after the relay is turned on for the OP time, the relay is turned off for the CL time, and then the above actions are cycled, the signal is given again in the cycle, the relay is turned off, and the timing is stopped; the number of cycles (LOP) can be set P6. No trigger signal is required after power-on, the relay is turned on for OP time, and the relay is turned off for CL time, and the above actions are repeated; the number of cycles (LOP) can be set; P7. If there is a trigger signal in the signal hold function, the timing will be cleared and the relay will remain on; when the signal disappears, the relay will be disconnected after timing OP; during timing, if there is another signal, the timing will be cleared; Timing range: 0.01 seconds (minimum) ~9999 minutes (maximum) continuously adjustable How to choose a timing range: In the OP/CL parameter modification interface, short press the STOP key to select the timing range XXXX has no decimal point, the timing range is 1 second to 9999 seconds The decimal point of XXX.X is in the ten place, and the timing range is 0.1 seconds and 999.9 seconds The decimal point of XX.XX is in the hundreds place, and the timing range is 0.01 seconds and 99.99 seconds X.X.X.X decimal points are all bright, the timing range is 1 minute 9999 minutes For example, if you want to set the OP to be 3.2 seconds, then move the decimal point to the ten place, and the LCD will display 003.2 Parameter description: OP on time, CL off time, LOP cycle times (1-9999 times, "----'' represents infinite cycles) Parameter settings: a) Press and hold the SET button to enter the setting interface; b) First set the working mode, the working mode flashes to remind, set the I working mode by short pressing the UP/DOWN button; c) Short press the SET key, select the working mode, and enter the system parameter setting; d) In the system parameter setting interface, short press the SET button to switch the system parameters to be modified, and short press and long press the UP/DOWN button to modify; (Note: Short press SET is invalid in P-1~p-3, P-7 mode); e) In the OP/CL parameter modification interface, short press STOP to switch the timing unit (1s/0.1s/0.01s/1min); f) All parameter settings are completed, long press the SET button to save the parameter settings and exit the setting interface; Package List: 1 x DC 6-30V Timer Relay Module with LED display
